226 - on 01.03.03 - The HT & LT Electrical Cublicles at the re-start of the restoration of 226 in 2003.
600x359
226200303A.jpg
2007-01-01 00:00:00
226 - High and low tension cabinets on 14.06.03 (Mike Collins)
600x404
226200306B.jpg
2007-02-28 00:00:00
226 - in 09.03 - The Bulkhead at the No.1 End before any work was done on it after the re-start of 226's restoration. (via Aidan Brosnan)
561x392
226200309A.jpg
2007-02-28 00:00:00
226 - The traction motor overload panels before and after Feb 2006 (Aidan Brosnan)
960x1280
226200602A.jpg
2002-01-01 00:01:33
226 - on 01.12.07 after attempting to fit half of cooler group. (Aidan Brosnan)
720x960
226200712B.jpg
2007-12-01 15:54:26
226 - on 10.08 - The generator at Bandon Rewinds awaiting overhaul. (via Aidan Brosnan).
640x480
226200810A.jpg
2004-01-01 00:00:00
226 - on 10.08 - The armature of the generator after starting its overhaul. (via Aidan Brosnan)
640x480
226200810Aa.jpg
2004-01-01 00:00:00
226 - on 10.08 - casing of Generator afterstart of Generator overhaul.(via Aidan Brosnan)
640x480
226200810Ab.jpg
2004-01-01 00:00:00
226 - on 10.11.08 - Water Tank welded to roof beam. (via Aidan Brosnan).
1280x960
226200811A.jpg
2008-11-10 20:22:54
226 - on 10.11.08 - Vacuum and water pipes cleaned and primed. (via Aidan Brosnan).
960x1280
226200811B.jpg
2008-11-10 20:23:29
226 - on 10.11.08 - Engine room panel cleaned and painted. (via Aidan Brosnan)
1280x960
226200811C.jpg
2008-11-10 20:25:18
226 - on 10.11.08 - Floor of engine room cleaned and door to Cab in place. (via Aidan |Brosnan).
960x1280
226200811D.jpg
2008-11-10 20:39:54
226 - - on 10.11.08 - door between cab No.2 and engine room. (via Aidan Brosnan).
960x1280
226200811Da.jpg
2008-11-10 20:21:05
226 - on 10.11.08 - Cab door handles attached and door to Engine room fitted from No.2 Cab. (via Aidan Brosnan).
1280x960
226200811F.jpg
2008-11-10 21:41:47
226 - shows the armature as it is being replaced inside the casing. (via Aidan Brosnan)
360x480
226200812A.jpg
2004-01-01 00:00:00
226 - on 12.08 - shows armature partially inserted into casing. Note the polished main and auxillary commutators (via Aidan Brosnan)
640x480
226200812Aa.jpg
2004-01-01 00:00:00
226 - on 12.08 - shows armature partially inserted into casing. Note the polished main and auxillary commutators (via Aidan Brosnan)
640x480
226200812Ab.jpg
2004-01-01 00:00:00
226 -on 12.08 - Generator set as auxiliary casing is being fitted (via Aidan Brosnan).
640x480
226200812Ac.jpg
2004-01-01 00:00:00
226 - On 12.08 - Generator before fitting of the auxiliary generator casing with the armature partially inserted into the casing. Note the extensive varnishing of the coils and the connections. (Via Aidan Brosnan).
640x480
226200812Ad.jpg
2004-01-01 00:00:00
226 - on 12.08 - show generator set with auxiliary generator casing replaced. (via Aidan Brosnan).
640x480
226200812Ae.jpg
2004-01-01 00:00:00
226 - on 12.08 - generator set with auxiliary generator casing replaced - note the old paint on the outside of the casing has been removed. (via Aidan Brosnan)
640x480
226200812Af.jpg
2004-01-01 00:00:00
226 - on 12.08 - end view of the auxiliary generator awaiting a new main bearing . Note the varnish applied to the coils. (via Aidan Brosnan)
640x480
226200812Ag.jpg
2004-01-01 00:00:00
226 - on 17.01.09 at Bandon Works Generator Terminal Box. (via Aidan Brosnan)
359x480
226200901Ga.jpg
2009-01-17 06:09:20
226 - on 17.01.09 at Bandon Works Cooler Motor after overhaul. (via Aidan Brosnan).
640x479
226200901Ta.jpg
2009-01-17 06:09:57
